In the case of a 2013 Subaru Outback with a check engine light and flashing brake light, the flashing brake light indicates a malfunction in the electronic parking brake system. It is important to promptly park in a safe location and contact a Subaru dealer for assistance.
If you own a 2013 Subaru Outback and are experiencing the frustrating issue of a check engine light combined with a flashing brake light, it’s important to understand the significance of this warning. The flashing brake light specifically indicates a malfunction in the electronic parking brake system.
This warning should not be ignored, as it signifies a potential issue that may require prompt attention and professional assistance from a Subaru dealer. We will delve deeper into what could be causing this warning and the appropriate steps to take for a resolution.
Credit: community.cartalk.com
Causes Of Check Engine And Brake Light Flashing
When the check engine and brake lights flash on a 2013 Subaru Outback, it may indicate issues with the electronic parking brake system or low brake fluid levels. Promptly park in a safe location and contact a SUBARU dealer for assistance to avoid potential brake failures.
When it comes to the 2013 Subaru Outback, a flashing check engine light and brake light can be indicators of potential issues. It’s important to understand the possible causes behind these warning lights to address the problem promptly. In this section, we will explore the three main categories of malfunctions and issues that could trigger the check engine and brake light flashing.
Possible Malfunctions In The Electronic Parking Brake System
If the electronic parking brake system malfunctions, it can trigger both the check engine and brake light to flash. This warning signals an issue that requires immediate attention. When you see these lights flashing, it’s crucial to park your vehicle in a safe location as soon as possible and reach out to your Subaru dealer for assistance.
Low Brake Fluid Or Hydraulic System Issues
A flashing brake light can indicate low or almost empty brake fluid, but it may also signal a significant problem with your vehicle’s hydraulic system. Ignoring this warning light can lead to potentially catastrophic brake failure, resulting in costly repairs. If the brake light comes on and stays on, it is essential to address the issue promptly to ensure your safety on the road.
Impact Of Minor Issues On Performance
Even minor issues can potentially affect the performance of the vehicle, which can be indicated by the check engine light. For example, a loose gas cap could trigger the light to come on consistently. While it may be safe to drive with such minor issues, any noticeable difference in performance should be taken seriously as it could be a sign of a more significant problem that requires immediate attention.
Credit: www.reddit.com
Troubleshooting The Check Engine And Brake Light Issues
If you’re experiencing a flashing check engine light and brake light on your 2013 Subaru Outback, it’s important to address the issue as soon as possible. Ignoring these warning lights could lead to serious mechanical problems and potential brake failure. In this section, we will discuss some common troubleshooting steps to help you identify and resolve the issue. Read on to find out how to successfully troubleshoot the check engine and brake light issues on your Subaru Outback.
Unplugging The Self Test Connector
One of the first steps in troubleshooting the check engine and brake light issues on your Subaru Outback is to unplug the self-test connector. This connector is located under your dashboard and is usually labeled as “diagnostic connector” or “self-test connector.” To unplug it, follow these steps:
- Locate the self-test connector under your dashboard.
- Using your fingers, gently pull the connector straight out to unplug it.
Once the self-test connector is unplugged, wait for about 10 seconds and then plug it back in. This will reset the system and may clear the check engine and brake light issues. If the lights continue to flash, it’s time to move on to the next troubleshooting step.
Gas Cap Inspection And Replacement
A loose or faulty gas cap can sometimes trigger the check engine light and brake light on your Subaru Outback. Inspecting and replacing the gas cap can help resolve this issue. Follow these steps to inspect and replace your gas cap:
- Locate the gas cap on your Subaru Outback.
- Twist the gas cap counterclockwise to loosen it.
- Inspect the gas cap for any signs of damage, wear, or debris.
- If the gas cap appears to be damaged or worn out, replace it with a new one.
- Twist the new gas cap clockwise to tighten it securely.
After replacing the gas cap, drive your Subaru Outback for a short distance to see if the check engine and brake lights have stopped flashing. If the lights persist, it’s time to move on to the next troubleshooting step.
Identifying The Wheel Speed Sensor Problem
A faulty wheel speed sensor can also cause the check engine and brake lights on your Subaru Outback to flash. To identify this problem, follow these steps:
- Inspect each wheel speed sensor for any signs of damage or wiring issues.
- If you notice any damaged or loose wiring, repair or replace it as necessary.
- Clear any debris or dirt that may be affecting the wheel speed sensor’s performance.
After inspecting and addressing any issues with the wheel speed sensors, drive your Subaru Outback to see if the check engine and brake lights continue to flash. If they do, it’s recommended to seek professional assistance from your Subaru dealer or a trusted mechanic to further diagnose and resolve the problem.
Remember, troubleshooting the check engine and brake light issues on your 2013 Subaru Outback requires careful attention and prompt action. By following the steps outlined above, you can take the necessary steps to resolve these issues and ensure the safety and performance of your vehicle.
Implications Of Check Engine And Brake Light On Vehicle Systems
Implications of Check Engine and Brake Light on Vehicle Systems2013 Subaru Outback Check Engine Light and Brake Light Flashing: The presence of a flashing check engine light and brake light in a 2013 Subaru Outback warrants attention. These warning indicators signal potential issues within the vehicle’s essential systems. Understanding the implications of these warning lights on various vehicle systems is crucial for maintaining the car’s safety and performance.
Effect on Cruise Control and Traction ControlEffect On Cruise Control And Traction Control
If the check engine light and brake light are flashing simultaneously in a 2013 Subaru Outback, the vehicle’s cruise control system may become disabled. The traction control, responsible for maintaining grip on slippery roads, could also be affected, impairing the car’s ability to navigate challenging driving conditions.
Disabled Systems’ Impact on DriveabilityDisabled Systems’ Impact On Driveability
The disabling of cruise control and traction control due to the flashing check engine and brake lights can significantly impact the driveability of the vehicle. This can lead to compromised control and handling, especially in adverse weather conditions or during long drives.
Resolving Check Engine And Brake Light Issues
Experiencing a flashing check engine light and brake light on your 2013 Subaru Outback can be alarming. In this guide, we will explore steps to resolve these issues effectively.
Contacting Subaru Dealer For Electronic Parking Brake System Malfunction
If the brake system warning light flashes due to an electronic parking brake system malfunction, it’s crucial to promptly contact your SUBARU dealer. Parking in a safe location is essential to address this issue efficiently.
Checking And Refilling Brake Fluid
If you notice a blinking brake light, it could indicate low or nearly empty brake fluid levels. Checking and refilling the brake fluid can help ensure the proper functioning of your vehicle’s brake system and prevent potential risks on the road.
Repairing Or Replacing Wheel Speed Sensor
In some cases, the flashing brake light could be related to a faulty wheel speed sensor. Repairing or replacing the wheel speed sensor can help resolve the issue and ensure the optimal performance of your Subaru Outback’s braking system.
Credit: www.reddit.com
Frequently Asked Questions On 2013 Subaru Outback Check Engine Light And Brake Light Flashing
Why Is The Brake Warning Light Flashing On My 2013 Subaru Outback?
The brake warning light is flashing on your 2013 Subaru Outback because of a malfunction in the electronic parking brake system. Park in a safe location and seek help from your SUBARU dealer immediately.
Why Is The Check Engine Light Blinking On My 2013 Subaru Outback?
The check engine light on your 2013 Subaru Outback is blinking to indicate a malfunction in the electronic parking brake system. Promptly park in a safe location and contact your Subaru dealer for assistance.
What Does It Mean When The Brake Light Is Blinking?
The brake light blinking could indicate a malfunction in the electronic parking brake system. If this happens, safely park your vehicle and contact your Subaru dealer for assistance. It could also signal low brake fluid or a serious issue with the hydraulic system, which could lead to brake failure if not addressed.
Can I Drive My Subaru Outback With The Check Engine Light On?
If the check engine light is on due to a minor issue like a loose gas cap, it is generally safe to drive. However, if you notice any changes in the car’s performance, it may indicate a more serious problem and it’s best to get it checked.
Conclusion
If your 2013 Subaru Outback has the check engine light and brake light flashing, it is important to address this issue promptly. Ignoring these warning lights could lead to more serious problems with your vehicle. Contact a professional Subaru dealer to diagnose and resolve the underlying issue with your car’s brake and engine system.
Taking immediate action is crucial to ensure the safety and performance of your vehicle.
- Check Engine Light Goes off After Getting Gas - March 31, 2024
- Check Engine Light Freightliner Cascadia - March 31, 2024
- Check Engine Light Ford Explorer - March 31, 2024
