2015 Dodge Durango Check Engine Light Reset: Expert Guide

To reset the check engine light on a 2015 Dodge Durango, fix the underlying issue or error code that caused it to turn on, such as a loose gas cap. Once the issue is resolved, the check engine light will usually shut off on its own.

However, you can also disconnect the battery for a few minutes and then reconnect it to clear the light if the fault has been repaired. It is not necessary to use an OBD scanner to clear the check engine light on a Dodge Durango.

This method may work but it is advisable to fix the underlying issue first.

Credit: www.bettenhausencdjr.com

Common Methods For Resetting

When the check engine light illuminates on your 2015 Dodge Durango, it can be quite concerning. However, there are several common methods you can try to reset the check engine light before seeking professional assistance. In this section, we will explore three popular methods for resetting the check engine light: disconnecting the battery, using an OBD scanner, and checking and tightening the gas cap.

Disconnecting The Battery

To reset the check engine light on your 2015 Dodge Durango, you can start by disconnecting the battery. This method is simple and can be done at home without any special tools. Follow these steps:

1. Locate the battery in the engine compartment.
2. Use a wrench to loosen and remove the negative (black) cable from the battery terminal. Make sure to disconnect the negative cable first.
3. Leave the battery disconnected for at least 15 minutes to allow the vehicle’s computer to reset.
4. After the time has elapsed, reconnect the negative cable to the battery terminal and tighten it securely.
5. Start your 2015 Dodge Durango to see if the check engine light has been successfully reset.

Using An Obd Scanner

An OBD (On-Board Diagnostic) scanner is a tool used to communicate with your vehicle’s computer system. It can read and clear diagnostic trouble codes, including the ones that trigger the check engine light. Follow these steps to reset the check engine light using an OBD scanner:

1. Plug the OBD scanner into the OBD port, which is usually located under the dashboard on the driver’s side.
2. Turn on the ignition without starting the engine.
3. Follow the instructions provided with your specific OBD scanner to navigate the menu and locate the option to clear diagnostic trouble codes.
4. Select the option to clear the codes and wait for the process to complete.
5. Once the codes have been cleared, turn off the ignition and unplug the OBD scanner.
6. Start your 2015 Dodge Durango to see if the check engine light has been successfully reset.

Checking And Tightening The Gas Cap

In some cases, a loose or faulty gas cap can trigger the check engine light. Before resorting to more advanced methods, it is recommended to check and tighten the gas cap on your 2015 Dodge Durango. Follow these steps:

1. Locate the gas cap on the driver’s side of your vehicle.
2. Ensure that the gas cap is securely in place.
3. Turn the gas cap clockwise to tighten it until you hear three clicks or until it feels snug.
4. Start your 2015 Dodge Durango to see if the check engine light has been successfully reset.

By following these common methods for resetting the check engine light on your 2015 Dodge Durango, you may be able to resolve the issue without the need for professional assistance. However, if the check engine light persists or if you are unsure about performing these procedures, it is always recommended to consult a qualified mechanic or technician.

Credit: www.hillviewmotors.com

Resetting Without A Mechanic

To reset the check engine light on a 2015 Dodge Durango without a mechanic, try disconnecting the battery for a few minutes. Reconnect it, and if the issue causing the light has been fixed, it should turn off after a few drive cycles.

This simple DIY method can save time and money.

If you’re a Dodge Durango owner and have noticed that dreaded check engine light illuminating on your dashboard, you may be wondering how to reset it without the help of a mechanic. While it’s always wise to have a professional diagnose and fix the issue causing the light to come on, there are some instances where you can perform a check engine light reset on your own.

Diy Check Engine Light Reset

If you’re confident in your abilities and want to try resetting the check engine light at home, here are some steps you can follow:

1. Start by ensuring that the problem causing the light to come on has been addressed. If you haven’t fixed the underlying issue, the light may come back on shortly after resetting it.
2. Next, grab your car’s user manual to locate the fuse panel. The fuse that controls the engine management system should be labeled “ECU” or “ECM”.
3. Once you’ve found the appropriate fuse, use a fuse puller or a pair of pliers to remove it.
4. Leave the fuse out for approximately 5 minutes to allow the system to reset.
5. After the allotted time, reinstall the fuse and make sure it’s securely in place.
6. Start your Durango’s engine and check to see if the check engine light has turned off. If it has, your reset was successful. If not, there may be a different underlying issue that needs to be addressed.

Tips For Resetting At Home

Here are some additional tips to keep in mind when attempting to reset the check engine light without a mechanic:

• Make sure your car is parked in a safe and well-ventilated area. You’ll need to have enough clearance and access to the fuse panel for a successful reset.
• Always consult your car’s user manual. Each vehicle may have specific instructions or fuse locations, so it’s important to follow the manufacturer’s guidelines.
• Consider investing in an OBD-II scanner. While not necessary for a basic reset, having an onboard diagnostic scanner can provide valuable information about the underlying issue causing the check engine light to come on.
• If the light comes back on after resetting, it’s time to see a mechanic. Continuing to drive with a illuminated check engine light can potentially cause further damage to your vehicle.

Remember, while a DIY check engine light reset can sometimes solve the issue, it’s always best to have a professional diagnose and repair any problems with your Dodge Durango. Performing regular maintenance and addressing issues promptly can help keep your vehicle running smoothly and efficiently.

When To Seek Professional Help

While you can reset the check engine light on a 2015 Dodge Durango yourself in many cases, there are times when it is best to seek assistance from a professional. Understanding the nuances of the check engine light and knowing when to seek help can help ensure the proper functioning of your vehicle and prevent potential issues from escalating.

Understanding Check Engine Light Codes

When the check engine light illuminates in your 2015 Dodge Durango, it indicates that the vehicle’s onboard diagnostic system has detected a problem. This system generates trouble codes that can provide crucial information about the issue at hand. Understanding these codes is essential in identifying the specific problem and determining the appropriate course of action. While you can use an OBD scanner to retrieve and interpret the codes yourself, seeking professional help may be necessary if the codes are unclear or if the issue is complex.

When The Light Indicates A Serious Issue

If the check engine light in your 2015 Dodge Durango indicates a serious issue, such as problems with the engine, transmission, or emissions system, it is crucial to seek professional help promptly. Ignoring these types of issues can lead to further damage and costly repairs. Additionally, attempting to reset the light without addressing the underlying problem can result in continued performance issues and potential safety hazards.

Credit: www.amazon.com

Frequently Asked Questions On 2015 Dodge Durango Check Engine Light Reset

How Do You Turn Off The Check Engine Light On A Dodge Durango?

To turn off the check engine light on a Dodge Durango, fix the issue that caused it to come on. Common fixes include tightening a loose gas cap or repairing the underlying problem. The light will usually reset on its own once the issue is resolved.

Can I Reset Check Engine Light Myself?

Yes, you can reset the check engine light yourself by disconnecting the battery for a few minutes, then reconnecting it. If the issue causing the light to come on is fixed, the light should turn off after a few drive cycles.

What Does The Check Engine Light Mean On A 2015 Dodge Durango?

The check engine light on a 2015 Dodge Durango indicates a problem or error with the vehicle. It will turn off automatically once the issue causing it is resolved.

Can You Clear A Check Engine Light Without A Scanner?

You can clear a check engine light without a scanner by disconnecting the battery for a few minutes and then reconnecting it. If the issue that caused the light to turn on has been fixed, the light should go out after a few drive cycles.

Conclusion

Resetting the check engine light on your 2015 Dodge Durango can be done easily by addressing the underlying issue that caused it to illuminate in the first place. By following the proper steps, such as tightening the gas cap or disconnecting the battery, you can clear the light and restore optimal performance to your vehicle.

Don’t let a check engine light cause unnecessary worry; with the right knowledge, you can resolve it efficiently.